Bobcat E50 Tracks: Size, Fit and Undercarriage Parts
The Bobcat E50 is listed with one track size, 400 x 72.5 x 74W: 400 mm (15.7 in) wide, with a 72.5 mm pitch and 74 links. This guide covers how to confirm the fit, the signs of wear and the E50 undercarriage parts to check at a track change.
Bobcat E50 Tracks: Size, Fit and Undercarriage Parts
Machine guideBobcat E506 min read
Looking for Bobcat E50 tracks? Our catalog lists the Bobcat E50 with one track size. This guide gives the Bobcat E50 track size, how to measure and confirm the fit, the signs that tracks are worn, and the undercarriage parts worth checking while the tracks are off.
The short answer
The Bobcat E50 track is listed as 400 x 72.5 x 74W: 400 mm (15.7 in) wide, with a 72.5 mm pitch and 74 links.
Our catalog lists one track variant for the E50. Tracks are sold per track.
At a track change, check the sprockets, idlers, bottom rollers and the 2 top rollers. We list the E50 top roller and bottom roller online; for the other parts, contact us.
Bobcat E50 track size
Our catalog lists one track size for the Bobcat E50. There is one listed variant, so the size below is the one to check against your machine.
Track size
Width
Pitch
Links
400 x 72.5 x 74W
400 mm (15.7 in)
72.5 mm
74
Source: Excavator Parts Direct catalog, October 2026. Sold as a single track (price is per track).
Read the size as width x pitch x links. A 400 x 72.5 x 74W track is 400 mm wide, has 72.5 mm between link centers and has 74 links. The E50 sits in the Bobcat E range of excavators, where the number in the model code gives the nominal size class.
Bobcat E50 rubber track, 400 x 72.5 x 74W.
How to measure a Bobcat E50 track
If the size is still readable on the side of your old track, use it. If it has worn away, take three measurements:
1
Width
Measure across the track from edge to edge. A Bobcat E50 track should measure 400 mm (15.7 in).
2
Pitch
Measure from the center of one link to the center of the next. The E50 track has a 72.5 mm pitch. Measure over several links and divide, which gives a truer figure than a single gap.
3
Links
Count the drive lugs around the inside of the track. The E50 track has 74. Mark your starting lug with chalk so you do not count one twice.
If your numbers match the table, you have the right size. Our guide to measuring rubber tracks shows each step with diagrams.
Four checks before you order Bobcat E50 tracks
1
Confirm the model
Check the model plate on the machine. Model codes can differ by a single character, and each model has its own listing. The E50Z, for example, has its own E50Z track listing. If the plate shows a different model, order for that model, or contact us with the machine details and serial number and we will check.
2
Match the size
Compare the size on the old track, or your measurements, with the table above. If the width is not 400 mm, the pitch is not 72.5 mm or the link count is not 74, stop and check before you order.
3
Check the tread
Our catalog lists one variant for the E50, and the listing does not name a tread pattern. If you want a particular tread, send us a photo of your current track and we will confirm what we can supply. Fit two tracks of the same tread so both sides grip and wear evenly.
4
Look underneath first
Before the new tracks go on, inspect the sprockets, idlers and rollers. New tracks on a worn undercarriage wear out sooner.
Our advice
A size that is checked, not guessed, is the quickest way back to work. If anything does not match, talk to the team before you order, so you maximize machine uptime and avoid a return.
Signs your Bobcat E50 tracks are worn
We recommend these checks on any tracked machine.
Damage to the rubber
Walk around the machine and look at the full length of each track. Deep cuts, missing lugs and steel cords showing through the rubber all mean the track is near the end of its life. A track in that state can fail without much warning.
Tension will not hold
If the track keeps going slack after you adjust it, do not assume the track is the cause. A track adjuster with failed piston seals cannot hold tension, and worn sprockets can add to the problem. Here is how to check rubber track tension. The correct tension figure for the E50 is in your machine’s operator’s manual. Our guide to excavator track adjusters explains how the adjuster works.
The track slips or jumps on the sprocket
When sprocket teeth wear sharp, they stop holding the track cleanly. The track can slip or jump through the sprocket, and the shock load travels into the final drive. If you see or hear this happen, stop and inspect the sprockets before you carry on.
The tracks wear out early
If a set of tracks wears out well before the last set did, look at the parts underneath before you fit new ones. Material packing between sprocket teeth, rollers and the track also speeds up wear, so keep the undercarriage clean. Our guide to spotting a worn sprocket shows what to look for, and these five tips to extend rubber track life cover other common causes.
Operating habits that add wear
Spinning the tracks, unnecessary reversing, high travel speed when it is not needed and always turning in the same direction all add wear. They wear the tracks and the sprockets that drive them.
Bobcat E50 undercarriage parts to check at a track change
With the tracks off, the whole undercarriage is in plain view. That makes a track change the best time to inspect it. Here is what our catalog shows for the E50:
Part
Listed online
What to check
Top roller
Yes: 2 per machine, 2.5 kg (5.5 lb) each
Turns freely, no oil leaks
Bottom roller
Yes: 9.3 kg (20.5 lb) each; ask the team for the quantity
Flat spots, worn flanges, oil leaks, rollers that do not turn
Drive sprocket
Not listed online: ask the team
Teeth worn sharp, track slipping or jumping
Idler
Not listed online: ask the team
Worn running surface, damaged flanges, oil leaks
Source: Excavator Parts Direct catalog, October 2026. Kilogram weights converted from the catalog’s pound figures.
Bobcat E50 top roller (left) and bottom roller (right).
Top rollers
Top rollers, also called carrier rollers, support the upper run of the track between the sprocket and the idler. Our catalog lists 2 E50 top rollers per machine. Check that each one turns freely and is not leaking oil. Our guide to bottom rollers and carrier rollers explains the difference.
Bottom rollers
Bottom rollers run along the underside of the track frame and carry the machine’s weight on the track. We list the E50 bottom roller online. Look for flat spots, worn flanges, oil leaks and rollers that no longer turn, and take time to check every one, including the rollers that are hard to see. We advise changing bottom rollers as a set, because a single new roller sits proud of the worn ones and wears faster. If you are not sure how many your machine needs, send us the serial number.
Drive sprockets
The sprocket bolts to the final drive and its teeth engage the track to drive the machine. We do not currently list an E50 sprocket online. Sprocket wear is hard to judge by eye, so compare yours with an unused sprocket of the same type. Wear builds faster in reverse and at higher travel speeds. If yours is worn, send us the serial number and we will check what we can supply.
Idlers and the track adjuster
Idlers guide the track around the end of the track frame and work with the track adjuster to hold tension. We do not currently list an E50 idler online. Check for worn running surfaces, damaged flanges and oil leaks. With an idler off, it is also the easiest time to check or replace the track adjuster. Our guide to excavator undercarriage parts covers each part in more detail.
Our advice
If the sprockets, idlers or rollers show wear, replace them with the tracks. It is one job and one round of downtime, and the new tracks start on a sound undercarriage. For parts we do not list online, speak to the team with your serial number.
Our catalog lists the Bobcat E50 track as 400 x 72.5 x 74W. It is 400 mm (15.7 in) wide, has a 72.5 mm pitch and has 74 links.
What does 400 x 72.5 x 74W mean?+
It is the track size, written width x pitch x number of links. The track is 400 mm wide, has a 72.5 mm pitch and has 74 links.
How wide is a Bobcat E50 track?+
The track our catalog lists for the Bobcat E50 is 400 mm (15.7 in) wide.
Are Bobcat E50 rubber tracks sold individually?+
Yes. We sell Bobcat E50 rubber tracks individually, and the price shown is for one track.
Is the Bobcat E50Z track the same as the E50 track?+
The E50 and E50Z are separate models in our catalog, and each has its own track listing. Check the model plate on your machine and order from the listing for that model.
How tight should Bobcat E50 tracks be?+
Use the tension figure in your machine’s operator’s manual. A track that is too loose can come off, and a track that is too tight wears faster. If the track will not hold tension, check the track adjuster.
Do you list sprockets or idlers for the Bobcat E50?+
Not online at the moment. We list the E50 rubber track, top roller and bottom roller. For other E50 undercarriage parts, contact us with the serial number and we will check what we can supply.
How do I know when my Bobcat E50 tracks need replacing?+
Common signs are deep cuts or exposed steel cords, a track that will not hold tension, a track that slips or jumps on the sprocket, and tracks that wear out much faster than the last set. Check the sprockets, idlers, rollers and track adjuster at the same time, because worn parts underneath shorten the life of new tracks.
Bobcat, E50 and E50Z are trademarks of their owner. The make and model names are used only to identify fitment. Excavator Parts Direct parts are aftermarket replacement parts, not genuine OEM parts, and Excavator Parts Direct is not affiliated with any manufacturer named.
CAT 239D tracks are listed in two sizes, 320 x 86 x 49B and 400 x 86 x 49B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 49 links, in C-lug or Z-lug tread. How to measure them, confirm the fit and check the sprockets and undercarriage.
John Deere 317G tracks are listed in two sizes, 320 x 86 x 50B and 400 x 86 x 50B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 50 links. How to measure them, confirm the fit and check the undercarriage parts around them.
The Kubota SVL65-2 is listed with two track sizes, 320 x 86 x 52B and 400 x 86 x 52B (86 mm pitch, 52 links), in a C-lug or Z-lug tread, and the SVL65-2C track is listed at 400 x 86 x 52B. This guide covers how to confirm the fit, the signs of wear and the SVL65-2 sprockets and bottom rollers to check.