Bobcat T630 Tracks: Size, Fit and Undercarriage Parts
The Bobcat T630 is listed with three track widths, 320, 400 and 450 x 86 x 52B (86 mm pitch, 52 links), each in a C-lug or Z-lug tread for the solid-mount undercarriage. This guide covers how to confirm the fit, the signs of wear and the T630 sprockets, idlers and bottom rollers to check.
Bobcat T630 Tracks: Size, Fit and Undercarriage Parts
Machine guideBobcat T6306 min read
Ordering new tracks for a Bobcat T630 starts with the size, and our catalog lists three track widths for this machine. This guide gives the Bobcat T630 track size in each width, the two tread patterns, how to confirm the fit, the signs that tracks are worn and the T630 sprockets, idlers and bottom rollers worth checking while the tracks are off.
The short answer
The Bobcat T630 track is listed as 320, 400 or 450 x 86 x 52B: 320 mm (12.6 in), 400 mm (15.7 in) or 450 mm (17.7 in) wide, all with an 86 mm pitch and 52 links.
Every width comes with a C-lug or Z-lug tread, is listed for the solid-mount undercarriage and is sold per track. Order the width that is on the machine now.
At a track change, check the 2 drive sprockets, the front and rear idlers and the bottom rollers.
Bobcat T630 track size
Our catalog lists three track sizes for the Bobcat T630 with the solid-mount undercarriage. The pitch and link count are the same on all three. Only the width changes, and each width comes in two treads.
Track size
Width
Pitch
Links
Tread
320 x 86 x 52B
320 mm (12.6 in)
86 mm
52
C-lug or Z-lug
400 x 86 x 52B
400 mm (15.7 in)
86 mm
52
C-lug or Z-lug
450 x 86 x 52B
450 mm (17.7 in)
86 mm
52
C-lug or Z-lug
Source: Excavator Parts Direct catalog, October 2026. Solid-mount undercarriage. Sold as a single track (price is per track).
Read the size as width x pitch x links. A 400 x 86 x 52B track is 400 mm wide, has 86 mm between link centers and has 52 links. If your old track shows a different pitch or link count, check with us before you order.
Bobcat T630 track, 320 x 86 x 52B. Left: C-lug tread. Right: Z-lug tread.
Which T630 track width to order
Match the width that is on the machine now. Read it from the size on the old track, or measure across the track from edge to edge. If you are thinking about a wider or narrower track, talk to the team first and tell us about the ground and the work.
Bobcat T630 tracks. Left: 400 x 86 x 52B, C-lug. Right: 450 x 86 x 52B, Z-lug.
How to measure a T630 track
If the size is still readable on your old track, use it. If it has worn away, take three measurements:
1
Width
Measure across the track from edge to edge. A T630 track should measure 320 mm (12.6 in), 400 mm (15.7 in) or 450 mm (17.7 in).
2
Pitch
Measure from the center of one link to the center of the next. The T630 track has an 86 mm pitch.
3
Links
Count the drive lugs around the inside of the track. The T630 track has 52.
If your numbers match one of the three widths, 86 and 52, you have the right size. Our guide to measuring rubber tracks shows each step with diagrams.
Four checks before you order T630 tracks
1
Match the size
Compare the size on the old track, or your measurements, with the table above. If the pitch is not 86 mm or the link count is not 52, stop and check before you order.
2
Confirm the undercarriage
Our T630 track, sprocket, idlers and bottom roller are listed for the solid-mount undercarriage. If you are not sure which undercarriage your machine has, contact us with the machine details and serial number and we will check.
3
Choose the width and tread
Order the width on the machine now, then choose a C-lug or Z-lug tread. The right tread depends on the ground the machine works on most and the jobs it does. Tell us about the work and we will help you choose.
4
Look underneath first
Before the new tracks go on, inspect the sprockets, idlers and bottom rollers. New tracks on a worn undercarriage wear out sooner.
Our advice
A size that is checked, not guessed, is the quickest way back to work. If anything does not match, talk to the team before you order, so you maximize machine uptime and avoid a return.
Signs your T630 tracks are worn
These are the checks we recommend on any tracked machine, and they apply to the T630.
Tension will not hold
If the track keeps going slack after you adjust it, do not assume the track is the cause. A track adjuster with failed piston seals cannot hold tension, and worn sprockets can add to the problem. Here is how to check rubber track tension. The correct tension figure for the T630 is in your machine’s operator’s manual.
The track slips or jumps on the sprocket
When sprocket teeth wear sharp, they stop holding the track cleanly. The track can slip or jump through the sprocket, and the shock load travels into the final drive. If you see or hear this happen, stop and inspect the sprockets before you carry on.
The tracks wear out early
If tracks wear out well before the last set did, check the parts underneath before you fit new ones. Material packing between sprocket teeth, rollers and the track also speeds up wear, so keep the undercarriage clean. Our guide to spotting a worn sprocket shows what to look for, and these five tips to extend rubber track life cover other common causes.
Operating habits that add wear
Spinning the tracks, unnecessary reversing, high travel speed when it is not needed and always turning in the same direction all add wear. They wear the tracks and the sprockets that drive them.
T630 sprockets, idlers and rollers to check at a track change
With the tracks off, the whole undercarriage is in plain view. That makes a track change the best time to inspect it. Here is what our catalog lists for the T630:
Part
Per machine
Weight each
Drive sprocket
2
44.0 kg (97 lb)
Idler
Front and rear positions
Not listed
Bottom roller
Ask the team
26.9 kg (59.3 lb)
Source: Excavator Parts Direct catalog, October 2026. Solid-mount undercarriage. Kilogram weights converted from the catalog’s pound figures.
The sprocket bolts to the final drive and its teeth engage the track to drive the machine. Our catalog lists 2 per T630. Sprocket wear is hard to judge by eye, so compare yours with an unused sprocket of the same type. Wear builds faster in reverse and at higher travel speeds.
Front and rear idlers
Idlers guide the track around each end of the track frame and work with the track adjuster to hold tension. Our catalog lists the T630 idler in the front and the rear position, so choose the one you need when you order. With an idler off, it is also the easiest time to check or replace the track adjuster.
Bobcat T630 idlers. Left: front idler. Right: rear idler.
Bottom rollers
Bottom rollers run along the underside of the track frame and carry the machine’s weight on the track. Look for flat spots, worn flanges, oil leaks and rollers that no longer turn. We advise changing bottom rollers as a set, because a single new roller sits proud of the worn ones and wears faster. Our guide to bottom rollers and carrier rollers explains the difference.
Our advice
If the sprockets, idlers or rollers show wear, replace them with the tracks. It is one job and one round of downtime, and the new tracks start on a sound undercarriage.
What we list for the Bobcat T630
These are the T630 parts in our catalog. Each is listed for the solid-mount undercarriage, and all four are on the Bobcat T630 parts page.
Our catalog lists three track sizes for the Bobcat T630 with the solid-mount undercarriage: 320 x 86 x 52B, 400 x 86 x 52B and 450 x 86 x 52B. All three have an 86 mm pitch and 52 links. Only the width changes.
How wide are Bobcat T630 tracks?+
The T630 track is listed in three widths: 320 mm (12.6 in), 400 mm (15.7 in) and 450 mm (17.7 in). Order the width that is on your machine now.
What does 400 x 86 x 52B mean?+
It is the track size, written width x pitch x number of links. The track is 400 mm wide, has an 86 mm pitch and has 52 links.
Can I change to a wider or narrower track on my T630?+
Our catalog lists all three widths for the T630, but the right width depends on the machine and the work. Talk to the team before you change width, and order the width on the machine now if you are unsure.
Can I get a Z-lug track for the Bobcat T630?+
Yes. Our catalog lists every T630 track width, 320, 400 and 450 mm, with a C-lug or a Z-lug tread.
Are Bobcat T630 tracks sold individually?+
Yes. We sell T630 tracks individually, and the price shown is for one track.
Does the Bobcat T630 have a front and rear idler?+
Our catalog lists the T630 idler in two positions, front and rear, for the solid-mount undercarriage. Choose the position you need when you order.
How do I know when my T630 tracks need replacing?+
Common signs are a track that will not hold tension, a track that slips or jumps on the sprocket, and tracks that wear out much faster than the last set. Check the sprockets, idlers, bottom rollers and track adjuster at the same time, because worn parts underneath shorten the life of new tracks.
Bobcat and T630 are trademarks of their owner. The make and model names are used only to identify fitment. Excavator Parts Direct parts are aftermarket replacement parts, not genuine OEM parts, and Excavator Parts Direct is not affiliated with any manufacturer named.
CAT 239D tracks are listed in two sizes, 320 x 86 x 49B and 400 x 86 x 49B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 49 links, in C-lug or Z-lug tread. How to measure them, confirm the fit and check the sprockets and undercarriage.
John Deere 317G tracks are listed in two sizes, 320 x 86 x 50B and 400 x 86 x 50B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 50 links. How to measure them, confirm the fit and check the undercarriage parts around them.
The Kubota SVL65-2 is listed with two track sizes, 320 x 86 x 52B and 400 x 86 x 52B (86 mm pitch, 52 links), in a C-lug or Z-lug tread, and the SVL65-2C track is listed at 400 x 86 x 52B. This guide covers how to confirm the fit, the signs of wear and the SVL65-2 sprockets and bottom rollers to check.