28/10/2026

CAT 257B Rubber Tracks: Track Size, Fit and Wear Checks

The CAT 257B rubber track is listed as 380 x 102 x 42: 380 mm (15 in) wide, with a 102 mm pitch and 42 links. How to measure it, confirm the fit and spot worn tracks and undercarriage parts.

CAT 257B Rubber Tracks: Track Size, Fit and Wear Checks

CAT 257B Rubber Tracks: Track Size, Fit and Wear Checks

Machine guideCAT 257B5 min read

Looking for CAT 257B rubber tracks? Our catalog lists one track size for this machine, so ordering is simple once the size is confirmed. This guide gives the CAT 257B track size, how to measure and check the fit, the signs that tracks are worn and the undercarriage parts worth checking while the tracks are off.

The short answer

  • The CAT 257B track is listed as 380 x 102 x 42: 380 mm (15 in) wide, with a 102 mm pitch and 42 links.
  • It is one size, sold per track. The 257B2 and 257B3 have their own listings, so check the model plate before you order.
  • At a track change, check the sprockets, idlers, rollers and track adjuster. New tracks on worn parts wear out sooner.

CAT 257B track size

Our catalog lists a single track size for the CAT 257B rubber track. There is one width and one variant, so there is no width to choose between.

Track size Width Pitch Links Sold as
380 x 102 x 42 380 mm (15 in) 102 mm 42 Per track

Source: Excavator Parts Direct catalog, October 2026. Sold as a single track (price is per track).

Read the size as width x pitch x links. A 380 x 102 x 42 track is 380 mm wide, has 102 mm between link centers and has 42 links. If your old track shows a different pitch or link count, check with us before you order.

CAT 257B rubber track, 380 x 102 x 42
CAT 257B rubber track, 380 x 102 x 42.

How to measure a 257B track

If the size is still readable on the old track, use it. If it has worn away, take three measurements:

1

Width

Measure across the track from edge to edge. A CAT 257B track should measure 380 mm (15 in).

2

Pitch

Measure from the center of one link to the center of the next. The 257B track has a 102 mm pitch.

3

Links

Count the drive lugs around the inside of the track. The 257B track has 42.

If your numbers come out at 380, 102 and 42, you have the right size. Our guide to measuring rubber tracks shows each step with diagrams.

Four checks before you order CAT 257B tracks

1

Confirm the model

Read the model plate. The 257B, 257B2 and 257B3 each have their own track listing in our catalog, so order from the one that matches your plate.

2

Match the size

Compare the size on the old track, or your measurements, with the table above. If the pitch is not 102 mm or the link count is not 42, stop and check before you order.

3

Check the tread

The listing gives the size only and does not name a tread pattern. If you need a particular tread, send us a photo of the old track and we will confirm what we can supply.

4

Look underneath first

Before the new tracks go on, inspect the sprockets, idlers, rollers and track adjuster. New tracks on a worn undercarriage wear out sooner.

Our advice

A size that is checked, not guessed, is the quickest way back to work. If anything does not match, talk to the team before you order, so you maximize machine uptime and avoid a return.

Signs your CAT 257B tracks are worn

These are the checks we recommend on any tracked machine, and they apply to the 257B.

Tension will not hold

If the track keeps going slack after you adjust it, do not assume the track is the cause. A track adjuster with failed piston seals cannot hold tension, and worn sprockets can add to the problem. Here is how to check rubber track tension. The correct tension figure for the 257B is in your machine’s operator’s manual.

The track slips or jumps on the sprocket

When sprocket teeth wear sharp, they stop holding the track cleanly. The track can slip or jump through the sprocket, and the shock load travels into the final drive. If you see or hear this happen, stop and inspect the sprockets before you carry on.

The tracks wear out early

If tracks wear out well before the last set did, check the parts underneath before you fit new ones. Material packing between sprocket teeth, rollers and the track also speeds up wear, so keep the undercarriage clean. Our guide to spotting a worn sprocket shows what to look for, and these five tips to extend rubber track life cover other common causes.

Operating habits that add wear

Spinning the tracks, unnecessary reversing, high travel speed when it is not needed and always turning in the same direction all add wear. They wear the tracks and the sprockets that drive them.

CAT 257B undercarriage parts to check at a track change

With the tracks off, the whole undercarriage is in plain view. That makes a track change the best time to inspect it. Here is what to look at, and what our catalog lists for the 257B today:

Part What to check Listed online for the 257B
Drive sprockets Teeth worn sharp, track slipping or jumping Not currently listed. Ask the team
Idlers Worn running surfaces, damaged flanges, oil leaks Not currently listed. Ask the team
Rollers Flat spots, worn flanges, oil leaks, rollers that do not turn Not currently listed. Ask the team
Track adjuster Track that will not hold tension, grease leaks See the Track Adjusters range

Source: Excavator Parts Direct catalog, October 2026.

Drive sprockets

The sprocket bolts to the final drive and its teeth engage the track to drive the machine. Sprocket wear is hard to judge by eye, so compare yours with an unused sprocket of the same type. Wear builds faster in reverse and at higher travel speeds. We do not currently list a 257B sprocket online. Browse CAT sprockets or contact us with the serial number.

Idlers and the track adjuster

Idlers guide the track around the end of the track frame and work with the track adjuster to hold tension. Check for worn running surfaces, damaged flanges and oil leaks. With an idler off, it is also the easiest time to check or replace the track adjuster. See CAT idlers for the CAT idlers we list.

Rollers

Rollers carry the machine’s weight on the track. Look for flat spots, worn flanges, oil leaks and rollers that no longer turn. We advise changing rollers as a set, because a single new roller sits proud of the worn ones and wears faster. Our guide to bottom rollers and carrier rollers explains the difference, and the CAT track rollers and CAT carrier rollers pages show what we list.

Our advice

If the sprockets, idlers or rollers show wear, replace them with the tracks. It is one job and one round of downtime, and the new tracks start on a sound undercarriage. If a part you need is not listed, contact us with the serial number and we will check.

What we list for the CAT 257B

Our catalog lists the CAT 257B rubber track. For the 257B2 and 257B3, use the listing for your model. All of our CAT tracks are on the CAT rubber tracks page.

TracksCAT 257B rubber track380 x 102 x 42. 380 mm (15 in) wide, 42 links. Sold per track.View part →UndercarriageCAT 257B sprockets, idlers and rollersNot currently listed online. Send us the serial number and the part you need.Contact us →

More CAT parts

FAQ

What size tracks does a CAT 257B take?+

Our catalog lists one track size for the CAT 257B: 380 x 102 x 42. That is 380 mm (15 in) wide, with a 102 mm pitch and 42 links.

How wide are CAT 257B tracks?+

The CAT 257B track is listed at 380 mm (15 in) wide. It is the only width we list for this machine.

What does 380 x 102 x 42 mean?+

It is the track size, written width x pitch x number of links. The track is 380 mm wide, measures 102 mm from the center of one link to the center of the next and has 42 links.

Do the CAT 257B, 257B2 and 257B3 use the same track listing?+

No. We list a separate track for each of these models. Check the model plate on your machine and order from the listing for that model. If the plate is hard to read, send us the serial number and we will check.

Are CAT 257B tracks sold individually?+

Yes. We sell CAT 257B tracks individually, and the price shown is for one track.

What tread pattern is the CAT 257B track?+

The listing gives the size only and does not name a tread pattern. If you need a particular tread, send us a photo of your old track and we will confirm what we can supply.

Do you sell CAT 257B sprockets, idlers and rollers?+

We do not currently list a sprocket, idler or bottom roller for the CAT 257B online. Contact us with the machine’s serial number and the part you need, and we will check what we can supply.

How do I know when my CAT 257B tracks need replacing?+

Common signs are a track that will not hold tension, a track that slips or jumps on the sprocket, and tracks that wear out much faster than the last set. Check the sprockets, idlers, rollers and track adjuster at the same time, because worn parts underneath shorten the life of new tracks.

Related guides

Need tracks or undercarriage parts for your 257B?

Tell us your machine, its serial number and what you need. We will confirm the right parts and send a quote. Shipped across the USA.

Get a quoteTalk to the team

CAT, Caterpillar, 257B, 257B2 and 257B3 are trademarks of their owner. The make and model names are used only to identify fitment. Excavator Parts Direct parts are aftermarket replacement parts, not genuine OEM parts, and Excavator Parts Direct is not affiliated with any manufacturer named.

Related news

11/11/2026

CAT 239D Tracks: Size, Fit and Undercarriage Parts

CAT 239D tracks are listed in two sizes, 320 x 86 x 49B and 400 x 86 x 49B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 49 links, in C-lug or Z-lug tread. How to measure them, confirm the fit and check the sprockets and undercarriage.

Find out more

11/11/2026

John Deere 317G Tracks: Size, Fit and Undercarriage Parts

John Deere 317G tracks are listed in two sizes, 320 x 86 x 50B and 400 x 86 x 50B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 50 links. How to measure them, confirm the fit and check the undercarriage parts around them.

Find out more

09/11/2026

Kubota SVL65-2 Tracks: Size, Fit and Undercarriage Parts

The Kubota SVL65-2 is listed with two track sizes, 320 x 86 x 52B and 400 x 86 x 52B (86 mm pitch, 52 links), in a C-lug or Z-lug tread, and the SVL65-2C track is listed at 400 x 86 x 52B. This guide covers how to confirm the fit, the signs of wear and the SVL65-2 sprockets and bottom rollers to check.

Find out more

Didn’t find what you need?

Contact our helpful sales team today.