28/10/2026

CAT 289D Tracks: Size, Fit and Undercarriage Parts

The CAT 289D is listed with one track size, 450 x 86 x 56B (450 mm / 17.7 in wide, 86 mm pitch, 56 links), in a C-lug or Z-lug tread. This guide covers how to confirm the fit, the signs of wear and the 289D sprockets, idlers and bottom rollers to check.

CAT 289D Tracks: Size, Fit and Undercarriage Parts

CAT 289D Tracks: Size, Fit and Undercarriage Parts

Machine guideCAT 289D6 min read

Looking for CAT 289D tracks? Our catalog lists the CAT 289D with one track size in two tread patterns. This guide gives the CAT 289D track size, how to confirm the fit, the signs that tracks are worn and the 289D sprockets, idlers and bottom rollers worth checking while the tracks are off.

The short answer

  • The CAT 289D track is listed as 450 x 86 x 56B: 450 mm (17.7 in) wide, with an 86 mm pitch and 56 links.
  • It comes with a C-lug or Z-lug tread, both in the same size. Tracks are sold per track.
  • At a track change, check the 2 drive sprockets, the front and rear idlers and the 10 bottom rollers.

CAT 289D track size

Our catalog lists one track size for the CAT 289D. Width, pitch and link count are fixed, so the only choice to make is the tread.

Track size Width Pitch Links Tread
450 x 86 x 56B 450 mm (17.7 in) 86 mm 56 C-lug
450 x 86 x 56B 450 mm (17.7 in) 86 mm 56 Z-lug

Source: Excavator Parts Direct catalog, October 2026. Sold as a single track (price is per track).

Read the size as width x pitch x links. A 450 x 86 x 56B track is 450 mm wide, has 86 mm between link centers and has 56 links.

C-lug or Z-lug for the 289D?

Both treads are listed in the same size, so the choice does not change the fit. It comes down to the ground the machine works on most. If you are unsure which suits your work, talk to the team and we will help you choose. If the old tracks did the job well, the simplest option is to order the same tread again.

CAT 289D rubber track, 450 x 86 x 56B, C-lug tread
CAT 289D rubber track, 450 x 86 x 56B, Z-lug tread
CAT 289D track, 450 x 86 x 56B. Left: C-lug tread. Right: Z-lug tread.

How to measure a CAT 289D track

Start with the size molded on the side of the old track. If it has worn away, take three measurements:

1

Width

Measure across the track from edge to edge. A CAT 289D track should measure 450 mm (17.7 in).

2

Pitch

Measure from the center of one link to the center of the next. The 289D track has an 86 mm pitch.

3

Links

Count the drive lugs around the inside of the track. The 289D track has 56. Mark your starting lug with chalk so you do not count one twice.

If all three numbers match the table, you have the right size. Our guide to measuring rubber tracks shows each step with diagrams.

Four checks before you order CAT 289D tracks

1

Confirm the model

Check the model plate on the machine. These sizes are for the machine listed in our catalog as the CAT 289D. Model codes can differ by a single character, and each model has its own listing. If the plate shows a different model, contact us with the machine details and serial number and we will check.

2

Match the size

Compare the size on the old track, or your measurements, with the table above. If the width is not 450 mm, the pitch is not 86 mm or the link count is not 56, stop and check before you order.

3

Choose the tread

Pick C-lug or Z-lug for the ground the machine works on. Fit two tracks of the same tread so both sides grip and wear evenly.

4

Look underneath first

Before the new tracks go on, inspect the sprockets, idlers and bottom rollers. New tracks on a worn undercarriage wear out sooner.

Our advice

A size that is checked, not guessed, is the quickest way back to work. If anything does not match, talk to the team before you order, so you maximize machine uptime and avoid a return.

Signs your CAT 289D tracks are worn

These are the checks we recommend on any tracked machine. Look at the tracks, then at the parts they run on.

Damage to the track itself

Deep cuts, missing lugs and steel cords showing through the rubber all mean the track is near the end of its life. A track in that state can fail without much warning, so plan the change before it stops the machine.

Tension will not hold

If the track keeps going slack after you adjust it, do not assume the track is the cause. A track adjuster with failed piston seals cannot hold tension. Here is how to check rubber track tension. The correct tension figure for the 289D is in your machine’s operator’s manual.

The track slips or jumps on the sprocket

When sprocket teeth wear sharp, they stop holding the track cleanly. The track can slip or jump through the sprocket, and the shock load travels into the final drive. If you see or hear this, stop and inspect the sprockets before you carry on.

Packing and operating habits

Material packed between the sprocket teeth, rollers and track speeds up wear, so keep the undercarriage clean. Spinning the tracks, unnecessary reversing, high travel speed when it is not needed and always turning in the same direction all add wear too. These five tips to extend rubber track life cover the habits that make the biggest difference.

CAT 289D sprockets, idlers and rollers to check at a track change

With the tracks off, the whole undercarriage is in plain view. That makes a track change the best time to inspect it. Here is what our catalog lists for the 289D:

Part Per machine Weight each What to check
Drive sprocket 2 Not listed Teeth worn sharp, track slipping or jumping
Idler Front (double or triple flange) and rear Not listed Worn running surfaces, damaged flanges, oil leaks
Bottom roller 10 27.8 kg (61.3 lb) Flat spots, worn flanges, oil leaks, rollers that do not turn
Track adjuster Not listed online Not listed Tension that will not hold, grease leaks. Ask the team

Source: Excavator Parts Direct catalog, October 2026. Kilogram weight converted from the catalog’s pound figure.

Drive sprocket for the CAT 289D
Bottom roller for the CAT 289D
CAT 289D undercarriage parts. Left: drive sprocket. Right: bottom roller.

Drive sprockets

The sprocket bolts to the final drive and its teeth engage the track to drive the machine. Our catalog lists 2 per 289D. Sprocket wear is hard to judge by eye, so compare yours with an unused sprocket of the same type. Wear builds faster in reverse and at higher travel speeds. Our guide to spotting a worn sprocket shows what to look for.

Front and rear idlers

Idlers guide the track around each end of the track frame and work with the track adjuster to hold tension. Our catalog lists three 289D idler options: a front idler with a double flange, a front idler with a triple flange, and a rear idler. Match the position and the flange type of the idler you are taking off. If you are not sure which you have, send us the serial number and a photo. With an idler off, it is also the easiest time to check or replace the track adjuster.

Front idler with double flange for the CAT 289D
Front idler with triple flange for the CAT 289D
Rear idler for the CAT 289D
CAT 289D idlers. Left to right: front idler, double flange; front idler, triple flange; rear idler.

Bottom rollers

Bottom rollers run along the underside of the track frame and carry the machine’s weight on the track. Our catalog lists 10 per 289D, so take time to check every one, including the rollers that are hard to see. Look for flat spots, worn flanges, oil leaks and rollers that no longer turn. We advise changing bottom rollers as a set, because a single new roller sits proud of the worn ones and wears faster. Our guide to bottom rollers and carrier rollers explains how each type works.

Our advice

If the sprockets, idlers or rollers show wear, replace them with the tracks. It is one job and one round of downtime, and the new tracks start on a sound undercarriage.

What we list for the CAT 289D

These are the 289D parts in our catalog. All four are on the CAT 289D parts page.

TracksCAT 289D rubber track450 x 86 x 56B, C-lug or Z-lug tread. Sold per track.View part →SprocketsCAT 289D drive sprocketCast steel with induction-hardened teeth. Our catalog lists 2 per machine.View part →IdlersCAT 289D front or rear idlerFront idler in double or triple flange, or rear idler. Heat-treated steel casing, sealed oil-filled shaft and bearings.View part →RollersCAT 289D bottom rollerHeat-treated steel casing, heavy-duty seals. Our catalog lists 10 per machine.View part →

More CAT parts

FAQ

What size tracks does a CAT 289D take?+

Our catalog lists one track size for the CAT 289D: 450 x 86 x 56B. That is 450 mm (17.7 in) wide, with an 86 mm pitch and 56 links. It is listed with a C-lug or Z-lug tread.

How wide are CAT 289D tracks?+

The CAT 289D track in our catalog is 450 mm (17.7 in) wide. Both listed treads, C-lug and Z-lug, use the same width.

What does 450 x 86 x 56B mean?+

It is the track size, written width x pitch x number of links. The track is 450 mm wide, has an 86 mm pitch and has 56 links.

Should I choose C-lug or Z-lug tracks for a CAT 289D?+

Both treads are listed in the same 450 x 86 x 56B size, so either one fits the same way. The better choice depends on the ground the machine works on most. Tell our team about the work and we will help you choose.

Are CAT 289D rubber tracks sold individually?+

Yes. We sell CAT 289D rubber tracks individually, and the price shown is for one track.

Which idler does a CAT 289D need?+

Our catalog lists the CAT 289D idler as a front idler with a double flange, a front idler with a triple flange, or a rear idler. Match the position and the flange type of the idler you are replacing. If you are not sure, send us the serial number and a photo.

How many bottom rollers and sprockets does a CAT 289D have?+

Our catalog lists 10 bottom rollers and 2 drive sprockets per machine for the CAT 289D.

How tight should CAT 289D tracks be?+

Use the tension figure in your machine’s operator’s manual. A track that is too loose can come off, and a track that is too tight wears faster, along with the parts it runs on.

How do I know when my CAT 289D tracks need replacing?+

Common signs are deep cuts, missing lugs or steel cords showing through the rubber, a track that will not hold tension, and a track that slips or jumps on the sprocket. Check the sprockets, idlers, bottom rollers and track adjuster at the same time, because worn parts underneath shorten the life of new tracks.

Related guides

Need tracks or undercarriage parts for your CAT 289D?

Tell us your machine, its serial number and what you need. We will confirm the right parts and send a quote. Shipped across the USA.

Get a quoteTalk to the team

CAT, Caterpillar and 289D are trademarks of their owner. The make and model names are used only to identify fitment. Excavator Parts Direct parts are aftermarket replacement parts, not genuine OEM parts, and Excavator Parts Direct is not affiliated with any manufacturer named.

Related news

11/11/2026

CAT 239D Tracks: Size, Fit and Undercarriage Parts

CAT 239D tracks are listed in two sizes, 320 x 86 x 49B and 400 x 86 x 49B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 49 links, in C-lug or Z-lug tread. How to measure them, confirm the fit and check the sprockets and undercarriage.

Find out more

11/11/2026

John Deere 317G Tracks: Size, Fit and Undercarriage Parts

John Deere 317G tracks are listed in two sizes, 320 x 86 x 50B and 400 x 86 x 50B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 50 links. How to measure them, confirm the fit and check the undercarriage parts around them.

Find out more

09/11/2026

Kubota SVL65-2 Tracks: Size, Fit and Undercarriage Parts

The Kubota SVL65-2 is listed with two track sizes, 320 x 86 x 52B and 400 x 86 x 52B (86 mm pitch, 52 links), in a C-lug or Z-lug tread, and the SVL65-2C track is listed at 400 x 86 x 52B. This guide covers how to confirm the fit, the signs of wear and the SVL65-2 sprockets and bottom rollers to check.

Find out more

Didn’t find what you need?

Contact our helpful sales team today.