02/11/2026

CAT 303.5 Tracks: Size, Fit and Undercarriage Parts

The CAT 303.5 is listed with one track size, 300 x 52.5 x 84W: 300 mm (11.8 in) wide, with a 52.5 mm pitch and 84 links. This guide covers how to confirm the fit, the signs of wear and the 303.5 bottom and top rollers to check at a track change.

CAT 303.5 Tracks: Size, Fit and Undercarriage Parts

CAT 303.5 Tracks: Size, Fit and Undercarriage Parts

Machine guideCAT 303.56 min read

Looking for CAT 303.5 tracks? Our catalog lists the CAT 303.5 with one track size, under the catalog model name 303.5 CR. This guide gives the CAT 303.5 track size, how to measure and confirm the fit, the signs that tracks are worn, and the undercarriage parts worth checking while the tracks are off.

The short answer

  • The CAT 303.5 track is listed as 300 x 52.5 x 84W: 300 mm (11.8 in) wide, with a 52.5 mm pitch and 84 links.
  • Our catalog lists one track variant for the 303.5. Tracks are sold per track.
  • At a track change, check the sprockets, idlers, the 8 bottom rollers and the 2 top rollers. We list the 303.5 bottom and top rollers online; for a sprocket or idler, contact us.

CAT 303.5 track size

Our catalog lists one track size for the CAT 303.5. There is one listed variant, so the size below is the one to check against your machine.

Track size Width Pitch Links
300 x 52.5 x 84W 300 mm (11.8 in) 52.5 mm 84

Source: Excavator Parts Direct catalog, October 2026. Sold as a single track (price is per track).

Read the size as width x pitch x links. A 300 x 52.5 x 84W track is 300 mm wide, has 52.5 mm between link centers and has 84 links. Model codes that start with a 3 belong to the CAT excavator range, and the digits after the first give the nominal size class.

CAT 303.5 rubber track, 300 x 52.5 x 84W
CAT 303.5 rubber track, 300 x 52.5 x 84W.

How to measure a CAT 303.5 track

If the size is still readable on the side of your old track, use it. If it has worn away, take three measurements:

1

Width

Measure across the track from edge to edge. A CAT 303.5 track should measure 300 mm (11.8 in).

2

Pitch

Measure from the center of one link to the center of the next. The 303.5 track has a 52.5 mm pitch.

3

Links

Count the drive lugs around the inside of the track. Mark your starting lug with chalk so you do not count one twice. The 303.5 track has 84.

If your numbers match the table, you have the right size. Our guide to measuring rubber tracks shows each step with diagrams.

Four checks before you order CAT 303.5 tracks

1

Confirm the model and generation

Check the model plate on the machine. On CAT excavators, a letter after the model number marks the generation, and our catalog lists the 303.5C CR, 303.5D CR and 303.5E CR on their own parts pages. If the plate shows one of those, order from that page, or contact us with the serial number and we will check.

2

Match the size

Compare the size on the old track, or your measurements, with the table above. If the width is not 300 mm, the pitch is not 52.5 mm or the link count is not 84, stop and check before you order.

3

Check the tread

Our catalog lists one variant for the 303.5, and the listing does not name a tread pattern. Fit two tracks of the same tread so both sides grip and wear evenly. If you want a particular tread, send us a photo of your current track and we will confirm what we can supply.

4

Look underneath first

Before the new tracks go on, inspect the sprockets, idlers and rollers. New tracks on a worn undercarriage wear out sooner.

Our advice

A size that is checked, not guessed, is the quickest way back to work. If anything does not match, talk to the team before you order, so you maximize machine uptime and avoid a return.

Signs your CAT 303.5 tracks are worn

We recommend these checks on any tracked machine.

Damage to the rubber

Walk around the machine and look at the full length of each track. Deep cuts, missing lugs and steel cords showing through the rubber all mean the track is near the end of its life.

Tension will not hold

If the track keeps going slack after you adjust it, do not assume the track is the cause. A track adjuster with failed piston seals cannot hold tension, and worn sprockets can add to the problem. Here is how to check rubber track tension. The correct tension figure for the 303.5 is in your machine’s operator’s manual.

The track slips or jumps on the sprocket

When sprocket teeth wear sharp, they stop holding the track cleanly. The track can slip or jump through the sprocket, and the shock load travels into the final drive. If you see or hear this happen, stop and inspect the sprockets before you carry on.

The tracks wear out early

If a set of tracks wears out well before the last set did, look at the parts underneath before you fit new ones. Material packing between sprocket teeth, rollers and the track also speeds up wear, so keep the undercarriage clean. Our guide to spotting a worn sprocket shows what to look for, and these five tips to extend rubber track life cover other common causes.

Operating habits that add wear

Spinning the tracks, unnecessary reversing, high travel speed when it is not needed and always turning in the same direction all add wear. They wear the tracks and the sprockets that drive them.

CAT 303.5 undercarriage parts to check at a track change

With the tracks off, the whole undercarriage is in plain view. That makes a track change the best time to inspect it. Here is what our catalog shows for the 303.5:

Part Listed online What to check
Bottom roller Yes: 8 per machine, 6.6 kg (14.6 lb) each Flat spots, worn flanges, oil leaks, rollers that do not turn
Top roller Yes: 2 per machine, 2.6 kg (5.7 lb) each Turns freely, no oil leaks
Drive sprocket Not listed online: ask the team Teeth worn sharp, track slipping or jumping
Idler Not listed online: ask the team Worn running surface, damaged flanges, oil leaks

Source: Excavator Parts Direct catalog, October 2026. Kilogram weights converted from the catalog’s pound figures.

Bottom rollers

Bottom rollers run along the underside of the track frame and carry the machine’s weight on the track. Our catalog lists 8 CAT 303.5 bottom rollers per machine. Look for flat spots, worn flanges, oil leaks and rollers that no longer turn, and take time to check every one, including the rollers that are hard to see. We advise changing bottom rollers as a set, because a single new roller sits proud of the worn ones and wears faster.

Bottom roller (track roller) for the CAT 303.5
CAT 303.5 bottom roller, second view
CAT 303.5 bottom roller (track roller), two views.

Top rollers

Top rollers, also called carrier rollers, support the upper run of the track between the sprocket and the idler. Our catalog lists 2 CAT 303.5 top rollers per machine. Check that each one turns freely and is not leaking oil. Our guide to bottom rollers and carrier rollers explains the difference.

Top roller (carrier roller) for the CAT 303.5
CAT 303.5 top roller, second view
CAT 303.5 top roller (carrier roller), two views.

Drive sprockets

The sprocket bolts to the final drive and its teeth engage the track to drive the machine. We do not currently list a 303.5 sprocket online. Sprocket wear is hard to judge by eye, so compare yours with an unused sprocket of the same type. Wear builds faster in reverse and at higher travel speeds. If yours is worn, send us the serial number and we will check what we can supply.

Idlers and the track adjuster

Idlers guide the track around the end of the track frame and work with the track adjuster to hold tension. We do not currently list a 303.5 idler online. Check for worn running surfaces, damaged flanges and oil leaks. With an idler off, it is also the easiest time to check or replace the track adjuster. Our guide to excavator undercarriage parts covers each part in more detail.

Our advice

If the sprockets, idlers or rollers show wear, replace them with the tracks. It is one job and one round of downtime, and the new tracks start on a sound undercarriage. For parts we do not list online, speak to the team with your serial number.

What we list for the CAT 303.5

These are the CAT 303.5 parts in our catalog. All three are on the CAT 303.5 CR parts page.

TracksCAT 303.5 rubber track300 x 52.5 x 84W. Continuously wound steel carcass. Sold per track.View part →RollersCAT 303.5 bottom rollerHeat-treated steel casing, sealed oil-filled shaft and bearings. Our catalog lists 8 per machine.View part →RollersCAT 303.5 top rollerHeat-treated steel casing, sealed oil-filled shaft and bearings. Our catalog lists 2 per machine.View part →

More CAT parts

FAQ

What size tracks does a CAT 303.5 take?+

Our catalog lists the CAT 303.5 track as 300 x 52.5 x 84W. It is 300 mm (11.8 in) wide, has a 52.5 mm pitch and has 84 links.

How wide are CAT 303.5 tracks?+

The CAT 303.5 track in our catalog is 300 mm (11.8 in) wide. It is the only width we list for the machine.

What does 300 x 52.5 x 84W mean?+

It is the track size, written width x pitch x number of links. The track is 300 mm wide, has a 52.5 mm pitch and has 84 links.

Are CAT 303.5 rubber tracks sold individually?+

Yes. We sell CAT 303.5 rubber tracks individually, and the price shown is for one track.

How tight should CAT 303.5 tracks be?+

Use the tension figure in your machine’s operator’s manual. A track that is too loose can come off, and a track that is too tight wears faster. If the track will not hold tension, check the track adjuster.

How many rollers does a CAT 303.5 have?+

Our catalog lists 8 bottom rollers and 2 top rollers per machine for the CAT 303.5.

Do you list sprockets or idlers for the CAT 303.5?+

Not online at the moment. We list the CAT 303.5 rubber track, bottom roller and top roller. For a sprocket or idler, contact us with the serial number and we will check what we can supply.

How do I know when my CAT 303.5 tracks need replacing?+

Common signs are deep cuts or exposed steel cords, a track that will not hold tension, a track that slips or jumps on the sprocket, and tracks that wear out much faster than the last set. Check the sprockets, idlers, rollers and track adjuster at the same time, because worn parts underneath shorten the life of new tracks.

Related guides

Need tracks or undercarriage parts for your CAT 303.5?

Tell us your machine, its serial number and what you need. We will confirm the right parts and send a quote. Shipped across the USA.

Get a quoteTalk to the team

CAT, Caterpillar and 303.5 are trademarks of their owner. The make and model names are used only to identify fitment. Excavator Parts Direct parts are aftermarket replacement parts, not genuine OEM parts, and Excavator Parts Direct is not affiliated with any manufacturer named.

Related news

11/11/2026

CAT 239D Tracks: Size, Fit and Undercarriage Parts

CAT 239D tracks are listed in two sizes, 320 x 86 x 49B and 400 x 86 x 49B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 49 links, in C-lug or Z-lug tread. How to measure them, confirm the fit and check the sprockets and undercarriage.

Find out more

11/11/2026

John Deere 317G Tracks: Size, Fit and Undercarriage Parts

John Deere 317G tracks are listed in two sizes, 320 x 86 x 50B and 400 x 86 x 50B: 320 mm (12.6 in) or 400 mm (15.7 in) wide, with an 86 mm pitch and 50 links. How to measure them, confirm the fit and check the undercarriage parts around them.

Find out more

09/11/2026

Kubota SVL65-2 Tracks: Size, Fit and Undercarriage Parts

The Kubota SVL65-2 is listed with two track sizes, 320 x 86 x 52B and 400 x 86 x 52B (86 mm pitch, 52 links), in a C-lug or Z-lug tread, and the SVL65-2C track is listed at 400 x 86 x 52B. This guide covers how to confirm the fit, the signs of wear and the SVL65-2 sprockets and bottom rollers to check.

Find out more

Didn’t find what you need?

Contact our helpful sales team today.