17/11/2026

Excavator Bucket Teeth: Types, Sizes and When to Replace Them

How excavator bucket tooth systems work, the main tooth types, how to find the right tooth size by measuring the back of the tip, and when to replace the set.

Excavator Bucket Teeth: Types, Sizes and When to Replace Them

Excavator Bucket Teeth: Types, Sizes and When to Replace Them

Buying guideExcavators7 min read

Bucket teeth are the cheapest part of a bucket and the part that does the most work. The right excavator bucket teeth depend on the tooth system on your bucket, the size of that system, and the ground you dig. This guide explains how a tooth system works, the main types of bucket teeth, how to find the right size, and when to replace them.

Key takeaways

  • Teeth are consumables. They wear so the adapters and the bucket lip do not.
  • Size comes from the bucket, not the tooth style. Pin-on teeth are sized by series, such as J250 or J350.
  • No reference? Measure the back of the tip. A tape across the back at the midpoint of the side walls gives the series.
  • Replace the full set before the lip is exposed, so the bucket loads evenly.

How a bucket tooth system works

A digging bucket carries a row of teeth across its cutting edge. The teeth concentrate the digging force so the bucket breaks into the ground. They also take the wear, which protects the bucket itself. For the bucket types that carry teeth, see our guide to excavator bucket types.

Most excavator buckets above mini size use a pin-on tooth system with four parts.

Part What it does
Tooth (tip) The replaceable point that does the digging. It slides over the adapter nose.
Adapter Fixed to the bucket lip. It carries the tooth and stays in place when the tooth is changed. Adapters are matched to the thickness of the cutting edge.
Pin Passes through the tooth and the adapter nose to hold the tooth on.
Retainer Locks the pin in place so it cannot work loose.

Adapters come in different forms. A twin strap adapter straddles the cutting edge, with one strap above and one below. A flush mounted adapter sits flush with the floor of the bucket. Both are sized to suit a range of edge thicknesses, so the adapter has to match the bucket as well as the tooth.

Pin-on excavator bucket tooth, J350 size, product listing image
A pin-on bucket tooth, as listed in J350 size.

Types of excavator bucket teeth

Within one tooth system, several tip styles fit the same adapter. The style changes how the tooth digs and how it wears. The size does not change.

Tooth style Shape Typical use
Standard long tip Long, general purpose profile Everyday digging in mixed ground
Rock chisel Chisel-shaped point Rocky and broken ground
Heavy-duty penetration Extra material at the point Hard, compacted ground
Heavy-duty abrasion Extra wear material on the body Abrasive material such as sand and gravel
Tiger tooth A single sharp, pointed tip Penetration in hard or frozen ground
Twin tiger tooth Two sharp points Hard ground, where two points help the tooth break in

Bucket teeth come in styles for applications from light construction to heavy mining.

Our advice

Choose the tooth for the ground you dig most of the time, not the hardest job of the year. If one bucket works in very different ground, ask the team whether a second set of teeth in a different style makes sense.

How to find the right tooth size

Pin-on teeth for mid-size and larger excavators are sized by series. The series number, such as J250 or J350, has to match the adapter on your bucket. A tooth from a different series will not fit, whatever the style.

1

Check the old tooth or adapter

Look for a series reference cast into the tooth or adapter. If it is readable, that is your size.

2

Measure the back of the tip

If the reference has worn off, place a tape measure across the back of the tip at the midpoint of the side walls.

3

Match the measurement to the series

Use the table below to turn the width into a series.

4

Check the machine size

Use the typical machine size as a cross-check, not as the answer. The bucket and adapter decide the tooth.

Series Width across back of tip Typical machine size Listed online
J200 2.0 in (51 mm) 4 to 6 metric tons Contact us
J225 2.25 in (57 mm) 6 to 8 metric tons J225 tooth
J250 2.5 in (64 mm) 10 to 12 metric tons J250 tooth
J300 3.0 in (76 mm) 15 to 20 metric tons J300 tooth
J350 3.5 in (89 mm) 20 to 25 metric tons J350 tooth
J400 4.0 in (102 mm) 25 to 30 metric tons J400 tooth
J460 4.5 in (114 mm) 34 to 40 metric tons J460 tooth
J550 5.5 in (140 mm) 45 to 50 metric tons J550 tooth

Each pin-on tooth we list is supplied with the pin and retainer. See all of them in our bucket teeth and wear parts range. If your bucket uses a different tooth system, or a series not listed, contact us with a photo of the tooth and adapter.

Tip

Measure two or three teeth, not just one. Teeth on the corners often wear differently from those in the middle, and a badly worn tip can read a size small.

Pin-on excavator bucket tooth, J250 size, product listing image
Teeth are sized by series. This listing is the J250 size.

Mini excavator bucket teeth

Many smaller mini excavator buckets use bolt-on teeth rather than pin-on teeth. A bolt-on tooth clamps over the cutting edge and is held by a bolt and nut through the edge. Sets are usually made up of left hand, center and right hand teeth, so the corner teeth protect the sides of the bucket.

Bolt-on teeth vary by bucket, so match the hole spacing, bolt size and edge thickness to the teeth you are removing. If you are unsure which system your bucket uses, send the team a photo of the bucket edge.

Looking for a new bucket rather than new teeth? See our excavator buckets, listed by machine, including CAT buckets, Hitachi buckets and John Deere buckets.

When to replace bucket teeth

Bucket teeth are consumable. They are meant to be replaced long before the bucket lip is exposed. Running teeth past their life moves the wear onto the adapter and then onto the lip, which is a far more expensive repair than a set of teeth.

Check the teeth as part of the daily walk-around. Replace them when you see:

  • Tips worn short or rounded, so the bucket no longer breaks into the ground cleanly
  • Wear reaching the adapter nose
  • A cracked, chipped or broken tooth
  • A tooth that moves on the adapter, or a missing or loose pin or retainer
  • Uneven wear across the set, with some teeth much shorter than others

Replace the whole set at once so the bucket loads evenly. When the teeth are off, check the adapters and the cutting edge as well. A worn adapter nose lets a new tooth rock, which wears the new tooth and the pin faster.

Pin-on excavator bucket tooth, J550 size, product listing image
Larger buckets take larger teeth. This listing is the J550 size.

The bottom line

Look at the total cost of ownership. The cheapest part is the one that keeps the machine working, and a set of teeth changed on time costs far less than a new adapter or a rebuilt bucket lip.

How to change a pin-on tooth

The steps below are a general guide. Follow the safety instructions in your machine's operator's manual, and wear eye protection when driving pins.

1

Make the machine safe

Lower the bucket to the ground or support it securely, turn the machine off and remove the key. Never work under a raised bucket.

2

Clean around the pin

Clear dirt from the tooth and the pin hole so the pin can be driven out.

3

Drive out the pin

Use a pin punch and hammer to drive the pin through. Keep the retainer if you are reusing it, but a new tooth is best fitted with a new pin and retainer.

4

Remove the old tooth and check the adapter

Pull the tooth off the adapter nose. Clean the nose and check it for wear or cracks.

5

Fit the new tooth

Fit the retainer in its recess, slide the new tooth onto the adapter and line up the holes. Drive the new pin home until it is flush.

6

Check the fit

The tooth should sit tight on the adapter with no rocking. Repeat for the rest of the set.

The rest of the machine matters too. A bucket only digs well on a machine that tracks well, so keep up with the excavator undercarriage parts checks, including track rollers and worn sprockets.

Buckets and wear parts

FAQ

What are the different types of excavator bucket teeth?+

The main styles are standard long tips for general digging, rock chisels, heavy-duty penetration tips, heavy-duty abrasion tips, and tiger or twin tiger teeth with a pointed tip. Most mid-size and larger buckets use pin-on teeth that fit over an adapter. Many mini excavator buckets use bolt-on teeth instead.

How do I know what size bucket teeth I need?+

Start with the tooth reference on the tooth or adapter you are replacing. Pin-on teeth are sized by series, such as J250 or J350. If the reference has worn off, measure across the back of the tip at the midpoint of the side walls. A 3.5 in (89 mm) reading, for example, points to a J350 tooth.

When should I replace excavator bucket teeth?+

Replace teeth long before the bucket lip is exposed. Once a tooth wears through, the wear moves to the adapter and then to the lip, which is a far more expensive repair. Replace the whole set at once so the bucket loads evenly.

Do mini excavators use different bucket teeth?+

Often, yes. Many smaller mini excavator buckets use bolt-on teeth that bolt through the cutting edge, with left hand, center and right hand teeth. Larger buckets usually use pin-on teeth fitted to adapters. Send the team a photo of the bucket edge if you are unsure which you have.

What holds a bucket tooth on the adapter?+

On a pin-on system, a pin passes through the tooth and the adapter nose, and a retainer locks the pin in place. The pin-on teeth we list online are supplied with the pin and retainer. Bolt-on teeth are held by a bolt and nut through the cutting edge.

Related guides

Not sure which teeth fit your bucket?

Send us the machine make and model, a photo of the tooth and adapter, and the width across the back of the tip. The team will check the tooth system and size for your bucket.

Talk to the teamGet a quote

Manufacturer names and model numbers are used for identification only. Excavator Parts Direct is an independent supplier of aftermarket parts and is not affiliated with any manufacturer named.

Related news

17/11/2026

Excavator Bucket Teeth: Types, Sizes and When to Replace Them

How excavator bucket tooth systems work, the main tooth types, how to find the right tooth size by measuring the back of the tip, and when to replace the set.

Find out more

17/11/2026

Compact Track Loader Parts: Undercarriage Parts Explained

A guide to the main compact track loader undercarriage parts: rubber tracks, sprockets, front and rear idlers, bottom rollers, carrier rollers and track adjusters. It explains what each part does, what to check, and the details you need to order the right parts.

Find out more

17/11/2026

Excavator Idlers: What a Front Idler Does and Signs of Wear

What an excavator idler does, the difference between front and rear idlers, the signs of a worn idler and what to check before you order a replacement.

Find out more

Didn’t find what you need?

Contact our helpful sales team today.