19/11/2026

When to Replace Skid Steer Tracks: Signs of Wear and Track Life

How to tell when skid steer and compact track loader tracks need replacing: six signs of wear, a six-step track check, and what to inspect on the undercarriage before new tracks go on.

When to Replace Skid Steer Tracks: Signs of Wear and Track Life

When to Replace Skid Steer Tracks: Signs of Wear and Track Life

MaintenanceCompact track loaders7 min read

Rubber tracks on a skid steer wear out with use. The question is when to change them. Replace too early and you waste track life. Leave it too late and a track can fail on the job, take a sprocket or roller with it and stop the machine. This guide shows the signs to look for, how to check a track and what to check before new tracks go on.

Key takeaways

  • Track life has no fixed number of hours. Ground, driving habits, tension and the rest of the undercarriage decide it.
  • Replace a track that shows exposed steel cords, deep cuts, lugs worn low, damaged links or will not hold tension.
  • Check sprockets, rollers, idlers and the track adjuster before fitting new tracks, so worn parts do not shorten their life.

A wheeled skid steer runs on tires. When people talk about skid steer tracks, they usually mean the rubber tracks on a compact track loader (CTL), or tracked skid steer. Everything in this guide applies to those machines, and most of it applies to rubber tracks on mini excavators too.

How long do skid steer tracks last?

There is no single answer, and any fixed figure should be treated with care. Two identical machines can get very different life from the same track. These are the factors that decide it:

  • Ground. Sharp rock, demolition debris, rebar and abrasive soil wear and cut rubber far faster than soil or turf.
  • Driving. High travel speed, long runs on hard surfaces and hard turns on the spot all add wear. A CTL can turn in its own length, and that turning puts side load on the tracks.
  • Tension. A track that runs too loose can come off. A track that runs too tight wears the track and the undercarriage faster.
  • Undercarriage condition. Worn sprockets, rollers and idlers wear a track out early and can make it come off.
  • Cleaning. Packed mud and debris add load and wear to every moving part.

The most useful figure is your own. Log the machine hours each time a set of tracks goes on. After one or two sets you will know what your machines get on your ground. Our 5 tips to extend the life of your rubber tracks cover the habits that make the biggest difference.

6 signs it is time to replace skid steer tracks

A rubber track is built from steel links (the cores the sprocket drives on) and high tensile steel cords, molded into a rubber carcass with tread lugs on the outside. Most replacement signs come from damage to one of those parts.

Sign What you see Why it matters
Exposed or broken steel cords Cuts or cracks deep enough to show the steel cords, or broken cord ends The cords carry the load around the track. Once they are exposed or broken, the track can fail without warning
Deep cuts and cracks Cuts across the track, cracks between the lugs or along the edges Cuts grow with use and let water reach the cords
Worn or missing lugs Tread lugs worn low or flat, or chunks of lug torn away Less grip and more slipping, especially on slopes and soft ground
Damaged steel links Links bent, broken, worn through or coming out of the rubber on the inside face The sprocket drives on the links, so damaged links stop the track running true
Track will not hold tension The track sags again soon after adjustment, or the adjuster has no travel left The track can come off. Check the track adjuster as well as the track
Track keeps coming off Repeated de-tracking with the tension set correctly A sign of a worn track, worn sprockets, rollers or idlers, or a failing adjuster
Rubber track for a CAT 259D compact track loader, 320 x 86 x 53B with Z-lug tread
Check the outer face for cuts, cracks and worn lugs. Shown: 320 x 86 x 53B Z-lug track listed for the CAT 259D.

Our advice

Do not wait for a track to break. A track that fails on the job can damage the sprocket, rollers or idlers on the way off, and it stops the machine where it stands. Order the replacement when the first signs appear, and fit it at a time that suits the work.

How to check your skid steer tracks

A full check takes a few minutes. Make it part of the routine on every machine, and do it more often on rough ground.

1

Park safely

Park on firm, level ground, lower the attachment to the ground, stop the engine and follow the safety steps in your machine's operator's manual.

2

Clean the tracks

Remove packed mud and debris so you can see the rubber, the links and the undercarriage parts behind them.

3

Check the full length

Inspect the outer face for cuts, cracks and worn or missing lugs. Move the machine forward to bring the hidden part of the track into view, then check again.

4

Check the inside face

Look at the steel links and the guide area for bent, broken or exposed links, and for rubber coming away from the steel.

5

Check the tension

Measure the track sag and compare it with the figure in your operator's manual. Adjust if needed. The method is in our track tension guide.

6

Record what you find

Note the machine hours, the condition of each track and any adjustment made. A record shows how fast wear is moving and when to order.

Tip

To measure tread wear, place a straight edge across two lugs and measure down to the track surface between them. Compare the depth over time, and against a new track of the same size. See how to tell a rubber track is worn.

Check the undercarriage before new tracks go on

New tracks on a worn undercarriage wear out early. When the old tracks come off, the sprockets, rollers and idlers are easy to see and easy to check. Our compact track loader undercarriage parts guide explains each part. The main checks:

  • Sprockets. The sprocket drives the track, and its pitch must match the track. Worn teeth can let a new track skip or come off. Here are 5 signs your sprocket is worn.
  • Bottom rollers. Look for rollers that do not turn, flat spots and oil leaks. Change bottom rollers together, so the track runs on an even set.
  • Idlers. Worn treads and flanges let the track wander. A leaking idler that has lost its oil fails quickly.
  • Track adjuster. If the track will not hold tension, the adjuster's piston seals may have failed. A broken spring or rod can leave the track far too tight. More in our track adjuster guide.
Drive sprocket for a Kubota SVL75 compact track loader
Check the sprocket teeth every time the tracks come off. Shown: sprocket for the Kubota SVL75.

Undercarriage parts

Ordering replacement skid steer tracks

The size is usually molded on the side of the track you are taking off. It is written as width x pitch x links. Width is in millimeters, pitch is the distance between link centers, and the last figure is the number of links. A letter in the size shows the tread or guide type. Check every part of the size, because some machines take more than one. If the size cannot be read, here is how to measure a rubber track.

Examples from our catalog:

Machine Track sizes listed Width Treads listed
Kubota SVL75 320 x 86 x 52B, 400 x 86 x 52B 12.6 in (320 mm), 15.7 in (400 mm) C-lug, Z-lug
Bobcat T650 320 x 86 x 52B, 400 x 86 x 52B, 450 x 86 x 52B 12.6 in (320 mm) to 17.7 in (450 mm) C-lug, Z-lug
CAT 259D 320 x 86 x 53B, 400 x 86 x 53B 12.6 in (320 mm), 15.7 in (400 mm) C-lug, Z-lug (320 mm)
John Deere 333G 450 x 86 x 58B 17.7 in (450 mm) C-lug

Every example above uses an 86 mm (3.4 in) pitch, but the link count differs from machine to machine. One link too many or too few and the track will not fit, so match the full size. Our tracks are priced per track.

Rubber track for a Kubota SVL75 compact track loader, 400 x 86 x 52B with C-lug tread
Match width, pitch, links and letter. Shown: rubber track for the Kubota SVL75, 400 x 86 x 52B C-lug.

Our advice

Replace both tracks together where possible. A new track beside a worn one gives uneven grip and uneven wear from side to side. Fit new tracks with the tension set to the figure in your operator's manual, then check it again after the first few hours of work.

Rubber tracks by make

FAQ

How long do skid steer tracks last?+

There is no single figure. Track life depends on the ground you work on, how the machine is driven, how well the tension is kept and the condition of the sprockets, rollers and idlers. A track that runs on abrasive ground, turns hard or runs too loose or too tight wears out far sooner than one on soft ground with good habits. Log the machine hours each time you fit a set, so you know what your own machines get.

When should you replace skid steer tracks?+

Replace a track when it shows exposed or broken steel cords, deep cuts or cracks, lugs worn low or missing, damaged steel links, or when it keeps coming off or will not hold tension after adjustment. Plan the change before the track fails on the job.

Can you replace just one skid steer track?+

You can, but our advice is to replace both tracks together where possible. A new track next to a worn one gives uneven grip and wear from side to side. If one track fails early from damage and the other is nearly new, talk to the team about the best option.

Should you replace the sprockets when you replace the tracks?+

Check them every time. A worn sprocket can let a new track skip or come off, and the sprocket pitch must match the track. If the sprocket teeth are worn, replace the sprocket with the tracks.

How do you know what size skid steer tracks to order?+

Read the size on the side of the track you are taking off. It is written as width x pitch x links, for example 400 x 86 x 52B, and the letter shows the tread or guide type. Check all of it against your machine's listing, because some machines take more than one size.

Related guides

Time for new tracks?

We list rubber tracks for compact track loaders and mini excavators, plus the sprockets, rollers and idlers that run with them. Send us the machine and the size on your old track, and the team will help you match it.

Get a quoteTalk to the team

Manufacturer names and model numbers are used for identification only. Excavator Parts Direct is an independent supplier of aftermarket parts and is not affiliated with any manufacturer named.

Related news

19/11/2026

When to Replace Skid Steer Tracks: Signs of Wear and Track Life

How to tell when skid steer and compact track loader tracks need replacing: six signs of wear, a six-step track check, and what to inspect on the undercarriage before new tracks go on.

Find out more

19/11/2026

John Deere 50G Tracks: Size, Fit and Undercarriage Parts

The John Deere 50G is listed with one track size, 400 x 72.5 x 74N: 400 mm (15.7 in) wide, with a 72.5 mm pitch and 74 links. This guide covers how to confirm the fit, the signs of wear and the 50G sprocket, idler and rollers to check at a track change.

Find out more

19/11/2026

Bobcat E32 Tracks: Size, Fit and Undercarriage Parts

The Bobcat E32 is listed with one track size, 300 x 52.5 x 80N: 300 mm (11.8 in) wide, with a 52.5 mm pitch and 80 links. This guide covers how to confirm the fit, the signs of wear and the E32 undercarriage parts to check at a track change.

Find out more

Didn’t find what you need?

Contact our helpful sales team today.